View
923
Download
18
Category
Preview:
Citation preview
Reconocimiento de:
Entendimiento del interes del cliente
Sistema o equipo a proteger
Levantamiento de planta o sistema o equipo
Cada cliente tiene diferentes intereses, sin duda, basado en sus intervenciones historicas o en su amplitud de criterio.
Unos estaran preocupados por el costo de los repuestos, otros por el lucro cesante y otros porinconfortabilidad , posicion ante la gerenciay/o colegas, al presentarse las fallas
En cada caso las protecciones deberan ser dirigidas a satisfacer estos intereses.
Sistema a proteger
Esto incluye todo un paquete de equipos, como puede ser un tren (linea) de produccion, un Data Center, un Sistema de elevadores, un CCM etc.
En cada caso se debera reconocer el flujo de la energia, desde los tableros de Acometida luegodistribucion hasta las propias maquinas o sub sistemas.
Un analisis sistematico de los circuitoselectricos y/o diagramas unifilares si se tratara de proteger todo un sistemaelectrico.
Debera ser analizado y preparado porun tecnico calificado
Los circuitos electricos se disenan bajo normas yasean internacionales o locales.
Los disenos pasaran por utilizar diversasconfiguraciones que se acomodan a las necesidades de los usuarios finales y a la disponibilidad de energia, yasea en alta, media o baja tension.
Para nuestro caso, se realiza desde media tension pordebajo de los 6900V
Monofasico 110 a 127 V 1P1
Monofasico 200 a 240 V 1P2
Monofasico 380 a 480 V 1P4
Bifasico 240/120 V 1S1
Bifasico 2 fases Sin Neutro 220V 2N2
Trifasico Estrella 208/120 3Y1
Trifasico Estrella 380/220 480/277 3Y2
Trifasico Delta 208/240 3N2
Trifasico Delta 380 a 480 3N4
Trifasico Delta 600V 3N6
Proteccion Total de Plantas
ANSI/IEEE Std 1100-1999
8.6.4 Premisa electrical de sistema de protection
In addition to surge protective devices installed in the service entrance equipment, it is recommended that additional surge protective devices of listed Category “B” or Category “A,” as specified in IEEE Std C62.41-1991, be applied to downstream electrical switchboards and panelboards, and panelboards on the secondary of separately derived systems if they support communications, information technology equipment, signaling, television, or other form of electronic load equipment.
16.16.1Interaction of surge-protective device operation on other protective devices
The SPDs covered in this guide are connected on the load side of the main overcurrent protective device inthe service entrance equipment. The device is typically a circuit breaker. The SPDs could be connected viaan additional circuit breaker downstream from the main overcurrent protective device. The surge currentcarrying capacity of the circuit breaker selected for use with an SPD should be considered in the applicationof the SPD. The suitability of a specific overcurrent protective device for use with a specific SPD, as itrelates to surge current carrying capacity, can be determined by either the manufacturer of the overcurrentprotective device or the manufacturer of the SPD.
Surge-protective device coordination
The need for coordination of overvoltage protective devices, such as SPDs, can best be compared with theunderstanding and requirements necessary for the coordination of overcurrent devices as fuses and circuitbreakers. The developments in overcurrent protection within the electrical industry and their applicationshave become a fine art; however, the evolution of overcurrent protective devices and their coordination didnot occur overnight.
The concept of SPD cascade coordination centers on the proper installation and connection of two or moreSPDs at different locations within a PDS. For example, one is connected to the service entrance equipment,and the other is connected in feeder or branch distribution panels or specific end-use equipment. Cascadecoordination is achieved when the SPD closest to the source of the impinging surge diverts most of theenergy from an impinging surge and a downstream SPD diverts the remaining or residual surge energy. Thesuccessful coordination of SPDs requires a thorough understanding of the specific PDS where SPDs are tobe connected and a thorough understanding of numerous variables that can affect the functionality of SPDs.Major variables affecting successful coordination of SPDs are as follows:
a) Waveshape and duration of an impinging surge.b) Distances between the SPDs and the PDS.c) Distance between the origin of a surge and the sensitive end-use equipment requiring protection.d) Measured limiting voltage of the SPDs.e) Surge current capacity of the SPDs.f) Age of the SPDs.g) Connections to, and integrity of, the grounding system of the PDS.h) Modes of protection selected for each SPD in the PDS.i) Configuration of a PDS.j) SPDs integrally connected within end-use equipment.
ST-LSEA
ST-SDLA
ST-CSLA
Legend
234 V
3.6 kV
70 kV
MAIN INCOMINGSECTION
DIST PANEL
HVAC
LIGHTING
234 V
234 V
0 V
0 V
0 V
43,200
Amps
Donde Necesito…
SUPRESORES DE TRANSITORIOS ?
A. Paneles Principales:Proteger contra Transitorios externos (Rayos, Conmutacionde sub estaciones por plantas vecinas y de distribucionelectrica, danos accidentales en lineas de fuerza).
B. Sub-Paneles de alimentacion a equipos criticosCentros de Distribucion, Centros de Control de Motores, Paneles de Breakers. Proteccion contra transitorios internos.
C. Algunos dispositivos individuales de Equipamientos:Protecccion contra transitorios generados internamente, es decir, proteger maquinas.
D. Lineas Telefonicas / Equipos de fax / Modems.Transmision de Data:
Proteccion contra Transitorios externos (Rayos).
Breakers 3000AmpPico de corriente300 kA por Fase
ServicioAcometida
Alta Exposicion
Breakers 2400AmpPico de corriente240 kA por fase
Breakers 1800AmpPico de Corriente180 kA por fase
Breakers 1200AmpPico de Corriente120 kA por fase
PanelesDistrib.
Breakers de 1800Amp Pico de Corriente180 kA por fase
Breakers de 1200AmpPico de Corriente120 kA por fase
Breakers de 600 a 750Pico de Corriente60-75 kA por fase
Media Exposicion
Breakers
Media a baja Exposicion
Breakers hasta 1200 AmpPico de Corriente120 kA por fase(
Breakers hasta 800 AmpPico de Corriente80 kA por fase
Baja Exposicion
Breakers hasta 600 AmpPico de Corriente60 kA por fase
Breakers hasta 400 Amp.Pico de corriente40 KA por fase
Sub Paneles
RM-ST60 or RM-ST120 units
Breakers hasta 900 AmpPico de Corriente90 kA por fase
Breakers hasta 600 AmpPico de Corriente60 kA por fase
PHONESDATA
PC
PCs
DIST.
SUBDIST.
DIST PANEL
PLC
PLC
PC
LAN
DIST PANEL
HVAC
• MODEM
PRINTER
PC
LINEMODEM
PC
PC
FROMPHONE Co.
FAXFROM POWER CO.
MAIN INCOMINGSECTION
LIGHTING
MCC
Machinery
SUBDIST.
FILESERVER
KSU
Robotics
Step 3A
Step 3B
No
Find Meter Gather Info
Move inside Locate main switch gearConfirm volts & amps
No YesOne
Switch
Followeach
switch run
Locate distributionpanels, sub-panels,breaker panels, fuseddisconnects orequipment
Confirmconfiguration,volts, & amps ofall panels &transformers
Is panel suppressionsufficient?
Determine if equipmentneeds point-of-use
protection
DedicatedCircuit
Determine type ofequipment serviced
by panel
MultipleSwitches
Yes
Moverse al interior de la planta hacia el panel principal o switch gear. Confirmar
voltaje y amperaje.
Paso 2
PHONESDATA
PC
PCs
DIST.
SUBDIST.
DIST PANEL
PLC
PLC
PC
LAN
DIST PANEL
HVAC
• MODEM
PRINTER
PC
LINEMODEM
PC
PC
FROMPHONE Co.
FAXFROM POWER CO.
MAIN INCOMINGSECTION
LIGHTING
MCC
Machinery
SUBDIST.
FILESERVER
KSU
Robotics
electricistasde la planta
debieranabrir
los panelessi alguien
estadisponible
Step 3A
Step 3B
No
Find Meter Gather Info
Move inside Locate main switch gearConfirm volts & amps
No YesOne
Switch
Locate distributionpanels, sub-panels,breaker panels, fuseddisconnects orequipment
Confirmconfiguration,volts, & amps ofall panels &transformers
Is panel suppressionsufficient?
Determine if equipmentneeds point-of-use
protection
DedicatedCircuit
Determine type ofequipment serviced
by panel
MultipleSwitches
Yes
No
Yes
Apply protection
Apply protection
Apply protection
Apply protection
Apply protection
CIRCUITINTERRUPT
DEVICE
SPD
NEUTRAL
PHASE A
PHASE B
PHASE C
GROUND
CIRCUITINTERRUPT
DEVICE
SPD
GROUND
PHASE A
PHASE B
PHASE C
SPD
PHASE A
PHASE B
PHASE C
CIRCUITINTERRUPT
DEVICE
NEUTRAL
GROUND
a
b c
i
j k l m n o p q
d e f g h r
s
t
u
a
b c
i
j k l m n o p q
d e f g h r
s
t
u
SPDSPD
SPDSPD
SPD
SPD
SPD
To dish
Air Conditioner
120/2401 Phase
200 A
Telephone Lines
Telephone KSU
Modem
SecuritySystem
VCR
Satellite Controller
Big Screen TV
Home Entertainment Center
GroundWire
60 Amp
To dish
Air Conditioner
120/2401 Phase
200 A
Telephone Lines
Telephone KSU
Modem
SecuritySystem
VCR
Satellite Controller
Big Screen TV
Home Entertainment
Center
GroundWire
60 Amp
SPD
SPD
SPD
SPD
120/2082 Phase200 A
copier CoffeePot
ProcessPC
Printer
Input
120 V13 A
CommonGround
SecuritySystem
TelephoneKSU
CommonGround
120 V20 A
Input Input
Input
PC
1000Foot Run
MiniComputer
Data Buss toProcess PC’s
ModemWarehouse
Inventory Control
Modem
PLCPLC
120/2082 Phase200 A
copier CoffeePot
ProcessPC
Printer
Input
120 V13 A
CommonGround
SecuritySystem
TelephoneKSU
CommonGround
120 V20 A
Input Input
Input
PC
1000Foot Run
Data Buss to
Process PC’s
ModemWarehouse
Inventory Control
Modem
PLCPLC
SPDSPD
SPDSPD
SPD
SPD
SPD
MiniComputer
SPD
MiniComputer
Modem
TelephoneKSU
Input
SecuritySystem
CheckoutRegister
RS 232 RegisterConnections
Lighting
Step DownTransformer
HVACSystem
PayrollSystems
Amenities
480 V3 Phase3000 A
CheckoutRegister
120/208 V3 Phase1000 A
120/208 V
120/208 V
Input
LV
MiniComputer
Modem
TelephoneKSU
Input
SecuritySystem
CheckoutRegister
RS 232 RegisterConnections
Lighting
Step DownTransformer
HVACSystem
PayrollSystems
Amenities
480 V3 Phase3000 A
CheckoutRegister
120/208 V3 Phase1000 A
120/208 V
120/208 V
Input
SPD
SPD
SPD
SPD
SPD
480 V3
Phase3000 A
Amenities
Apartments &Condominiums
ProfessionalOffices
Restaurants &
Snack Bars
Dry Cleaners& Laundry
Panel 1
120/208 V
3 Phase1000 A
Panel 2
Panel 3
Panel 4
DistributionPanelStep Down
Transformer
Amenities
Apartments &Condominiums
ProfessionalOffices
Restaurants &Snack Bars
Dry Cleaners& Laundry
Panel 1
120/208 V3 Phase1000 A
480 V3 Phase3000 A
Panel 2
Panel 3
Panel 4
DistributionPanel
Step DownTransformer
SPD
SPD
SPD
SPD
SPD
SPD
Step DownTransformer
Input
ProcessPC
Printer
VFD
VFD
VFD
ArcWelder
SpecialBuilding
Controller
CNCControl
CPU
CNCMachine
Tool
IntegratedProcess Machine
Tool & CPU
Step DownTransformer
240 Delta
480 V3 Phase800 A
JunctionBox
120 V 20 A1 Phase
480 V3 Phase800 A
120/240 V3 Phase200 A
240 Delta
120 V 15 A
480 V3 Phase1200 A
Amenities
Step DownTransformer
Step DownTransformer
Step DownTransformer
Input
ProcessPC
Printer
VFD
VFD
VFD
ArcWelder
SpecialBuilding
Controller
CNCControl
CPU
CNCMachine
Tool
IntegratedProcess Machine
Tool & CPU
Step DownTransformer
240 Delta
480 V3 Phase800 A
JunctionBox
480 V3 Phase800 A
120/240 V3 Phase200 A
240 Delta
120 V 15 A
480 V3 Phase1200 A
Amenities
Step DownTransformer
SPD
SPD
SPD
SPD
SPD
SPD
SPD
Step DownTransformer
SPD
SPD
SPD
SPD
SPD
o
a
b
j
p
q
g
r
ih
de f
m
n
l
k
c
a
b
j
o
p
q
g
r
ih
de f
m
n
l
k
c
SPDSPDSPD
oa
b
j
p
q
g
r
ih
de f
m
n
l
k
c
Note: Multiple SPD/TVSS applications(s) on very long section of mains switchgear
SPD SPD SPDSPD
Es importante anotar que esta sugerencia es exactamente ello – Son solo sugerencias. La aplicacion de los supresores puede considerarse un arte y no precisamente una ciencia. El rango de amperaje de las cargas es minimamente aceptable. Los supresores son dispositivos en paralelo, entonces el amperaje de la carga no es critica para la operacion de la unidad.
Usted siempre debe utilizar la unidad de mayor amperaje que se encuentra en la carga. Por favor no use uno menor. Ej. Usar una unidad LA-ST60 en un panel de 1000 amp. No es recomendable, Sin embargo puede desearinstalar una unidad LA-ST240 en un panel de 400 amp para lograr un buengrado de descarga en un tablero donde se espera, por ejemplo un rayo.
Iniciando con el mas critico y sensible equipo. Aislar el equipo del ambiente electrico por seleccion de la mas apropiada unidad.
En cualquier situacion donde el equipo es inusual voltaje o el tipo de coneccion puede ser diferente que el normal – Hacer un dibujo y enviarlo a quien puede hacer una buena recomendacion.
Nunca diga al cliente que no podemos ayudarlo. Digale que haremos las consultas a fabrica para obtener una solucion.
PLC’S ST-SPT120 (240-380-480) 15
Fuentes de poder monofasicas ST-SPT120 (240-380-480) 15
Fuentes de poder Trifasicas RM-ST40A3N2(4)
ST-RSE3N2(4)
Variadores de frecuencia Hasta 20 HP ST-RSE3N2 (4)
Variadores de frecuencia Hasta 40 HP RM-ST40A3N2(4)
Variadores de frecuencia Hasta 75 HP RM-ST60A3N2(4)
Variadores de frecuencia Hasta 100 HP RM-ST120A3N2(4)
Variadores de frecuencia hasta 200 HP RM-ST120A3N2(4)
Variadores de frecuencia hasta 300 HP RM-ST180A3N2(4)
Acometidas, tableros principales hasta 900 Amp ST-SSLA
Acometidas, tableros principales hasta 1200 Amp ST-SKLA
Acometidas, tableros principales hasta 1800 Amp ST-SDLA
Acometidas, tableros principales hasta 2400 Amp ST-LSEA
Acometidas, tableros principales hasta 3000 Amp ST-SMLA
Acometidas, tableros principales hasta 3600 Amp ST-SILAM
Acometidas, tableros principales hasta 4800 Amp ST-SHLAM
Acometidas, tableros principales hasta 6000 Amp ST-SHDLAM
Tableros de distribución Hasta 250 Amp RM-ST40A
Tableros de distribución Hasta 400 Amp RM-ST60A
Tableros de distribución Hasta 600 Amp RM-ST120A
Tableros de distribución Hasta 800 Amp RM-ST120A
Tableros de distribución Hasta 1200 Amp RM-ST180A
Tableros de distribución Hasta 1800 Amp LA-ST180A
Tableros de distribución Hasta 2400 Amp LA-ST240A
Tableros de distribución Hasta 3000 Amp LA-ST300A
Maquinas industriales:
Potencia RM-ST…, LA-ST…,
Control ST-SPT…,
Comunicaciones ST-CL24…, ST-RS232…, etc.
UPS’S Verificar capacidad, configuracion y
alimentacion
Ej:
UPS True On Line Doble Conversion 30KVA
Trifasico Y 380/220
Entrada: LA-ST60A3Y2C
Salida si fuera necesario RM-ST60A3Y2C
General Recommendations
Traffic Lights: combination unit – ST-SPT120-15-RJ
Slot Machines / Tragamonedas: 3 phase panel – LA-ST60-3Y1C
Bank ATM: ST-SPT120-15-RJ. If the data is not telephone but data circuit, then need data information –wires and voltage and useST-SPT-120-RJ45.
Video Surveillance Systems: Protect the AC and the cameras. Combination units are available. 120 AC, 24DC, Coax… Acquire all information.
Remember… this is not an
exact science, it is an
artform.
1P
2N2
1S1
3Y
3N
Single Line Drawing
Main Transformer
WYE SYSTEMAvailable Modes of Protection
Phase A
Neutral
Phase B
Phase C
Ground
1
2
3
4
5
6
7
89
10
1 - Phase A to Neutral2 - Phase B to Neutral3 - Phase C to Neutral4 - Phase A to Ground5 - Phase B to Ground6 - Phase C to Ground7 - Neutral to Ground8 - Phase A to Phase B9 - Phase A to Phase C10 - Phase B to Phase C
Wye System – Modes available
3 Modes protected
WYE SYSTEMOnly 3 Modes Protected
Phase A
Neutral
Phase B
Phase C
Ground
4 Modes protected
WYE SYSTEMOnly 4 Modes Protected
Phase A
Neutral
Phase B
Phase C
Ground
7 Modes protected
WYE SYSTEMOnly 7 Modes Protected
Phase A
Neutral
Phase B
Phase C
Ground
10 Modes protected
WYE SYSTEMAll 10 Modes Protected
Phase A
Neutral
Phase B
Phase C
Ground
Service Entrance
HVAC Distribution Panel
Branch Panel
Integrated Load Center
REV DATA APROBCOMPANY No. SYSTEM
1 31/ene/2006 IA 1TVSS MOLIENDAA-G
VAR 20 HP
440 vac
LA--ST-2403N4C
Soft
Starter
500 hp
Soft
Starter
500 hp
LA--ST-603N4C LA--ST-1203N4C LA--ST-1203N4C
Generador Juan
Esta es la configuración en Alfagres de la
molienda.
Cuando entra la planta eléctrica, inician
primero el motor de 500 hp, después el otro
de 500. estos en el arranque alcanzan hasta
2000 amp en aproximadamente 45
segundos. La pregunta es :
Afectara esto alos supresores que
instalaremos en cada arrancador ?????
La pregunta es, a que voltaje sostenido puede
llegar en ese momento, si la tension supera el
MCOV en 3 ciclos probablemente se danaran, si
no, no pasa nada. Tipicamente los arranques
producen un aumento de corriente pero no de
voltaje.! Por ende no pasara nada.
ALFAGRES , PLANTA DE GRES
PLC PANT.
1
PANT.
2
DRIVE
20 HP
ST-RSE-3N4
3 X 50 A
FUENTE
ST-SPT 24DC- 15
RECTIFICADOR
24 V DC
MAQ. 520
440 VAC
PLC PANT.
1
PANT.
2
DRIVE
20 HP
DRIVE
3 HP
DRIVE
3 HP
ST-RSE-3N4
3 X 40 A 3 X 25 A
ST-RSE-3N4
FUENTE
MAQ. 510
3x100A
24 V DC
440 VAC
220 Vac
3 x 100 Amp 220 Vac
Q1Q2
1F 440 Q1
1 NEUTRO
1F 440 Q2
1 NEUTRO
3 AMP
3 AMP
AUHF-30-440-60D-EOPAUHF-30-440-60D-EOP
MODELO AMPER.
CAPACID.
DE
DESCARGA
VOLT.
CONFIGURA
CION
SEGUIMIEN
TO DE
ONDA
MODOS
DE
PROTECCI
ON MODELO
FINAL
ST RSE 200 20 Ka. 240 Monofasica NO 2 ST RSE 1P2
ST RSE 200 20 Ka. 240 Trif. Delta NO 3 ST RSE 3N2
ST RSE 200 20 Ka. 380 Trif. Delta NO 3 ST RSE 3N4
ST RSE 200 20 Ka. 440 Trif. Delta NO 3 ST RSE 3N4
ST RSE 200 20 Ka. 380/220 Trif. Estrella NO 4 ST RSE 3Y2
MODELO AMPERAJE
CAPACIDAD DE
DESCARGAVOLTAJE CONFIGURACION
SEGUIMIENTO
DE ONDA
MODOS DE
PROTECCIONMODELO FINAL
RM ST 40 250 25 Ka. 240 Monofasica SI 3 RM ST 40 1P2
RM ST 40 250 25 Ka. 240 Trif. Delta SI 6 RM ST 40 3N2
RM ST 40 250 25 Ka. 380 Trif. Delta SI 6 RM ST 40 3N4
RM ST 40 250 25 Ka. 440 Trif. Delta SI 6 RM ST 40 3N4
RM ST 40 250 25 Ka. 380/220 Trif. Estrella SI 7 RM ST 40 3Y2
RM ST 60 400 40 Ka. 240 Monofasica SI 3 RM ST 60 1P2
RM ST 60 400 40 Ka. 240 Trif. Delta SI 6 RM ST 60 3N2
RM ST 60 400 40 Ka. 380 Trif. Delta SI 6 RM ST 60 3N4
RM ST 60 400 40 Ka. 440 Trif. Delta SI 6 RM ST 60 3N4
RM ST 60 400 40 Ka. 380/220 Trif. Estrella SI 7 RM ST 60 3Y2
RM ST 120 800 80 Ka. 240 Monofasica SI 3 RM ST 120 1P2
RM ST 120 800 80 Ka. 240 Trif. Delta SI 6 RM ST 120 3N2
RM ST 120 800 80 Ka. 380 Trif. Delta SI 6 RM ST 120 3N4
RM ST 120 800 80 Ka. 440 Trif. Delta SI 6 RM ST 120 3N4
RM ST 120 800 80 Ka. 380/220 Trif. Estrella SI 7 RM ST 120 3Y2
RM ST 180 1200 120 Ka. 240 Monofasica SI 3 RM ST 180 1P2
RM ST 180 1200 120 Ka. 240 Trif. Delta SI 6 RM ST 180 3N2
RM ST 180 1200 120 Ka. 380 Trif. Delta SI 6 RM ST 180 3N4
RM ST 180 1200 120 Ka. 440 Trif. Delta SI 6 RM ST 180 3N4
RM ST 180 1200 120 Ka. 380/220 Trif. Estrella SI 7 RM ST 180 3Y2
MODELO AMPERAJE
CAPACIDAD
DE DESCARGA VOLTAJE
CONFIGURACIO
N
SEGUIMIENT
O DE ONDA
MODOS DE
PROTECCION MODELO FINAL
LA ST 60 600 60 Ka. 240 Monofasica SI 3 LA ST 60 1P2C
LA ST 60 600 60 Ka. 240 Trif. Delta SI 6 LA ST 60 3N2C
LA ST 60 600 60 Ka. 380 Trif. Delta SI 6 LA ST 60 3N4C
LA ST 60 600 60 Ka. 440 Trif. Delta SI 6 LA ST 60 3N4C
LA ST 60 600 60 Ka. 380/220 Trif. Estrella SI 10 LA ST 60 3Y2C
LA ST 120 1200 120 Ka. 240 Monofasica SI 3 LA ST 120 1P2C
LA ST 120 1200 120 Ka. 240 Trif. Delta SI 6 LA ST 120 3N2C
LA ST 120 1200 120 Ka. 380 Trif. Delta SI 6 LA ST 120 3N4C
LA ST 120 1200 120 Ka. 440 Trif. Delta SI 6 LA ST 120 3N4C
LA ST 120 1200 120 Ka. 380/220 Trif. Estrella SI 10 LA ST 120 3Y2C
LA ST 180 1800 180 Ka. 240 Monofasica SI 3 LA ST 180 1P2C
LA ST 180 1800 180 Ka. 240 Trif. Delta SI 6 LA ST 180 3N2C
LA ST 180 1800 180 Ka. 380 Trif. Delta SI 6 LA ST 180 3N4C
LA ST 180 1800 180 Ka. 440 Trif. Delta SI 6 LA ST 180 3N4C
LA ST 180 1800 180 Ka. 380/220 Trif. Estrella SI 10 LA ST 180 3Y2C
LA ST 240 2400 240 Ka. 240 Monofasica SI 3 LA ST 240 1P2C
LA ST 240 2400 240 Ka. 240 Trif. Delta SI 6 LA ST 240 3N2C
LA ST 240 2400 240 Ka. 380 Trif. Delta SI 6 LA ST 240 3N4C
LA ST 240 2400 240 Ka. 440 Trif. Delta SI 6 LA ST 240 3N4C
LA ST 240 2400 240 Ka. 380/220 Trif. Estrella SI 10 LA ST 240 3Y2C
LA ST 300 3000 300 Ka. 240 Monofasica SI 3 LA ST 300 1P2C
LA ST 300 3000 300 Ka. 240 Trif. Delta SI 6 LA ST 300 3N2C
LA ST 300 3000 300 Ka. 380 Trif. Delta SI 6 LA ST 300 3N4C
LA ST 300 3000 300 Ka. 440 Trif. Delta SI 6 LA ST 300 3N4C
LA ST 300 3000 300 Ka. 380/220 Trif. Estrella SI 10 LA ST 300 3Y2C
MODELO AMPERAJE
CAPACIDAD DE
DESCARGA
VOLTAJE CONFIGURACION
SEGUIMIENTO
DE ONDA
MODOS DE
PROTECCION
MODELO FINAL
ST SPT120-15 15 40 Ka. 120 Monofasica SI 3 ST SPT120-15
ST SPT120-30 30 40 Ka. 120 Monofasica SI 3 ST SPT 120-30
ST SPT240-15 15 40 Ka. 240 Monofasica SI 3 ST SPT 240-15
ST SPT240-30 30 40 Ka. 240 Monofasica SI 3 ST SPT 240-30
ST-SPT380-15 15 40 Ka. 380 Monofasica SI 3 ST-SPT380-15
ST-SPT380-30 30 40 Ka. 380 Monofasica SI 3 ST-SPT380-30
ST-SPT480-15 15 40 Ka. 480 Monofasica SI 3 ST-SPT480-15
ST-SPT480-30 30 40 Ka. 480 Monofasica SI 3 ST-SPT480-30
EJEMPLO
VDF15KW
61 AMP3F/220
2F/220v
24v/20A
UPS24v
CPU
24vPLC
SIG SIMONAZZI
DANFOSS
3x220vac
1000 AMP
3F/380v 3F/380v 3F/380v
24v/40A24v/40A24v/40A
LA-ST120-3Y1 C 6-
0731-7767
ST RSE-3N2
906-306-101
80 AMP
LA-ST60-3Y1 C
9-0626-7052
ST-SPT-2N2-158-0710-4272
Primario 3x220v
Primario
3x380vST-RSE-3N4
9-0629-6068
200AMP
Mezclador
LA-ST60-3Y1
9-0626-7050
2F/220v
24v/20A
PLC
2Fases220v
ST-RSE-3N2
9-0630-6100
ST-RSE-3N2
9-0630-6096
ST-STP2N2-15
8-0710-4269
100 AMP
Empacadora I
LA-ST60-3Y1C
9-0626-7054
3F/220v
24v/20A
250AMP
3F/220v
24v/20A
Empacadora II
Horno I
3F/220v
24v/20A
3F/220v
24v/20A
Horno II
250AMP
LA-ST60-3Y1C
9-0626-7053
ST-RSE-3N2
9-0630-6102
ST-RSE-3N2
9-0630-6097
LA-ST603Y1C
9-0626-7051LA-ST60-3Y1C
9-0626-7055
ST-RSE-3N2
9-0630-6099
100 AMP
10AMP
PLC220v
ST SPT-2N2
8-0710-4273
Rechazador120vac
Video Yet120vac
LA-ST601S1C
8-0711-4365
ST-SPT-120-15
8-0910-5356
CPU24v
CPU24v
CPU
120v
ST-SPT120-15
8-0910-5357
Rechazador Llenadora
LA-ST-60-3N4SC
¿ En donde podemos instalar la unidad
LA-ST-1203N4C-SC ? En la entrada
11,4 kv / 60 Hz
451 vac
440 vac
220 vac
1 31/ene/2006 IA 1TVSS MOLIENDAA-G
VAR 20 HP440 vac
LA--ST-2403N4C
Soft Starter500 hp
Soft Starter500 hp
LA--ST-603N4C LA--ST-1203N4C LA--ST-1203N4C
Generador Juan
Esta es la configuración en Alfagres de la molienda.
Cuando entra la planta eléctrica, inician primero el motor de 500 hp, después el otro de 500. estos en el arranque alcanzan hasta 2000 amp en aproximadamente 45 segundos. La pregunta es :
Afectara esto alos supresores que instalaremos en cada arrancador ?????
La pregunta es, a que voltaje sostenido puede llegar en ese momento, si la tension supera el MCOV en 3 ciclos probablemente se danaran, si no, no pasa nada. Tipicamente los arranques producen un aumento de corriente pero no de voltaje.! Por ende no pasara nada.
1 31/ene/2006 IA 1TVSSA-G
Trafo
440/220 vac
24vdc
3x30 amp
440 vac 60Hz
Fuente Ac/Dc
PLC
Servo 1kw / 380 vac
LA-ST-603N4
Trafo
440/380
Trafo
440/220 vac
24vdc
3x30 amp
440 vac 60Hz
Fuente Ac/Dc
PLC
Servo 1kw / 380 vac
ST-SPT-240-15
Trafo
440/380
Trafo
440/220 vac
24vdc
3x30 amp
440 vac 60Hz
Fuente Ac/Dc
VFD
PLC
ST-SPT-240-15
Trafo
440/380
ST-SPT-240-15
LA-ST-603N4 LA-ST-603N4
TABLERO DE SUB DISTRIBUCION
LA-ST1203N4C
MAQUINA 1 MAQUINA 2 MAQUINA 3
ST-RSE3N4
1 G R 1TVSS - FUERZAEMPACOR
125 HP / 440 VAC
3 PHM
GABINETE 1
LA-ST-603N4C
3 PHM
100 HP / 440 VAC
75 HP / 440 VAC
3 PHM
3 PHM
75 HP / 440 VAC
75 HP / 440 VAC
3 PHM
3 PHM
75 HP / 440 VAC
3 x 600 A
440 VAC
40 HP / 440 VAC
GABINETE 2
LA-ST-603N4C
3 PHM
40 HP / 440 VAC
3 PHM
3 PHM
30 HP / 440 VAC
40 HP / 440 VAC
3 PHM
3 PHM
30 HP / 440 VAC
3 x 200 A
440 VAC
40 HP / 440 VAC
GABINETE 3
LA-ST-603N4C
3 PHM
40 HP / 440 VAC
3 PHM
3 PHM
30 HP / 440 VAC
75 HP / 440 VAC
3 PHM
3 PHM
75 HP / 440 VAC
3 x 300 A
440 VAC
LA-ST1203N4
Recommended