View
214
Download
0
Category
Preview:
Citation preview
DIM - Modulador COFDM
ESP
M A N U A L D E U S U A R I O
11INTRODUCCIÓN
22INSTRUCCIONES DE SEGURIDAD
33AJUSTES DE FUNCIONAMIENTO
44CONEXIONES
55INSTALACIÓN
66EJEMPLO DE INSTALACIÓN
77ESPECIFICACIONES TÉCNICAS
Gracias por la compra de este modulador digital terrestre. Lea este manual detenidamente para instalar, utilizar y mantener el modulador en las condiciones de funcionamiento óptimas. Guarde el manual cerca del modulador para futuras consultas. El producto que ha adquirido es un modulador de última generación cuyas principales características son:
Modulador DVB-T compatible con estándar ETSI EN 300 744 v1.5.1 Totalmente compatible con el estándar DVB-T/H. Entrada de vídeo en CVBS (a través de puerto RCA) o S-VHS. Estéreo. Bandas VHF y UHF (47~862 MHz) Generación de tablas PSI: PAT, PMT; SI: SDT, NIT. Generación de LCN. Formatos de vídeo PAL y NTSC. Operación en modo 2K. Constelaciones de 16QAM y 64QAM.
La supervisión y el control del DIM se realiza a través de la pantalla LCD situada en el panel frontal. Éste se congura mediante un conjunto de menús de navegación intuitiva.
Cualquier manipulación indebida puede ser peligrosa y puede llevar a cabo la invalidez de la garantía. El modulador se alimenta con una tensión de 7.5 Vdc. La fuente de alimentación no debe superar esa tensión en caso contrario el modulador podría sufrir daños irreparables y la consiguiente invalidación de la garantía. Por tanto: - No sustituya la fuente de alimentación por una de tensión superior a 7.5 Vdc. - No conecte el modulador a la corriente si el cable está dañado. - No conecte el modulador a la corriente hasta que no haya llevado a cabo todas las conexiones pertinentes. - No corte el cable de alimentación. No acerque ningún recipiente que contenga líquidos al modulador para evitar derrames y salpicaduras. No instale el modulador cerca de ningún dispositivo que desprenda calor ni en lugares de elevada humedad. No cubra el modulador con elementos que obstruyan las ranuras de ventilación y evite su sobrecalentamiento. Si el modulador ha estado sometido largo tiempo a bajas temperaturas deberán pasar al menos 2 horas a una temperatura más cálida antes de poder enchufar la fuente de alimentación. Montar el modulador en posición vertical con las conexiones hacia abajo. Es conveniente dejar un espacio libre de al menos 10 cm en todos los lados del modulador. Conectar el chasis a una toma de tierra mediante el terminal destinado a tal n. (ver apartado 5-B)
Por defecto, los parámetros del modulador son:- Canal de salida: C28- Atenuación: 30%- Constelación: QAM16- FEC: 3/4
3.2 CONFIGURACIÓN RÁPIDA
3.3 CONFIGURACIÓN AVANZADA
- Intervalo de guarda: 1/16- PID Vídeo: 33- PID Audio: 34- Región de canales: EUROPA OESTE
- Nombre de canal: CH A- Nombre red: NET A- Entrada de vídeo: CVBS- Estándar de vídeo: PAL
Tras la puesta en marcha, en la pantalla aparece la versión del rmware durante 4 segundos. A continuación aparece: “Iniciando...”, durante ese período de tiempo el modulador está cargando el rmware e iniciando dispositivos internos. Una vez iniciado aparece en pantalla: “Modulando XX (FFFFFF) kHz”. Este mensaje nos indica el canal de salida del modulador, siendo XX el número de canal (puede variar entre E2 y C69) y FFFFFF la recuencia en kHz incluyendo el ajuste no.
Conmute el idioma del menú al inglés manteniendo simultáneamente pulsados los botones al conectar la alimentación del modulador.
3.1 INICIO DEL MODULADOR
Si desea realizar un cambio rápido de canal pulse las teclas y para conrmar.
CANAL DE SALIDAC60 (786000 kHz)
MENUBASICO
MENUAVANZADO
OK
Ajuste el nivel de salida del modulador.
Seleccione el idioma del menú de usuario.
Pulse OK para acceder al menú y seleccione “MENU BASICO” pulsando nuevamente OK.
En este menú puede ajustar parámetros básicos como: canal de salida, atenuación e idioma.
MENU BASICOCANAL DE SALIDA
CANAL DE SALIDAC60 (786000 kHz)
MENU BASICOATENUACION
ATENUACIONXXX %
MENU BASICOIDIOMA
IDIOMAESPAÑOL
MENU BASICOSALIR
Con los botones ajuste el canal de salida y pulse OK para conrmar.
Ajuste no de la frecuencia central del canal (± 100kHz).
Ajuste del nivel de salida del modulador.
Cambio de constelación (QAM16, QAM64).
Ajuste del FEC (1/2, 2/3, 3/4, 5/6, 7/8).
Ajuste del intervalo de guarda (1/8, 1/16, 1/32).
Seleccione el PID de vídeo / audio (33 – 8190).
Puede congurar la posición de su canal modulado en la red de distribución. Opción desactivable.
Seleccione el estándar de vídeo que desee utilizar.PAL o NTSC.
Seleccione la entrada de vídeo que quiere utilizar.
Restaura los parámetros por defecto del modulador.
Ajuste el nivel de brillo/contraste/saturaciónde la imagen.
Seleccione el idioma del menú de usuario.
Pulse OK para acceder al menú y seleccione “MENU AVANZADO” pulsando nuevamente OK. Este menú permite ajustar los parámetros avanzados del modulador.
MENU AVANZADOCANAL DE SALIDA
CANAL DE SALIDAC60 (786000 kHz)
MENU AVANZADOAJUSTE FINO
AJUSTE FINO786000 kHz
Seleccione la región de canales a utilizarMENU AVANZADOREGION CANALES
REGION CANALESEUROPA OESTE
MENU AVANZADOATENUACION
ATENUACIONXXX %
MENU AVANZADOCONSTELACION
CONSTELACIONQAM16
MENU AVANZADOFEC
FEC7/8
MENU AVANZADOINT. GUARDA
INT. GUARDA1/16
MENU AVANZADOPID VIDEO
PID VIDEO33
MENU AVANZADONOMBRE CANAL
NOMBRE CANALCH A
MENU AVANZADOLCN
LCN3
MENU AVANZADOFUENTE DE VIDEO
FUENTE DE VIDEOCVBS
MENU AVANZADOESTANDAR VIDEO
ESTANDAR VIDEOPAL
MENU AVANZADOBRILLO
BRILLO123
MENU AVANZADOIDIOMA
IDIOMAESPAÑOL
MENU AVANZADOCONF. ORIGINAL
MENU AVANZADOSALIR
Cambie el nombre del canal: con los botones seleccione el carácter y pulse OK para conrmar.**
Con los botones ajuste el canal de salida y pulse OK para conrmar.
Cambie el nombre.Seleccione el carácter que desea cambiar con los botones , observe que el carácter aparece sombreado y parpadeando, presione “OK” para seleccionar el carácter (aparecerá subrayado) y con las teclas seleccione el nuevo carácter, conrme el cambio con “OK”. Para guardar el nombre, avance con hasta el nal de la línea (observe que no parpadea ningún caracter) y presione “OK”. El nuevo nombre quedará almacenado en memoria.
El ajuste del BITRATE de vídeo y audio debe hacerse dentro de los límites permitidos para la conguración de modulación escogida (constelación, FEC e intervalo de guarda)
Alimentación: 7,5VDC/2A.Conector RS-232 para PC.Salida RF modulada.Entrada de vídeo S-VHS.Entrada de vídeo RCA.Entrada de Audio Derecho RCA.Entrada de Audio Izquierdo RCA.Conexión de toma de tierra.
1
2
3
5
6
7
4
8
2 3
4 5 6 7 8
1
A - Atornille el modulador en el lugar donde desea instalarlo.
Fuente deaudio/vídeo
C - Conecte los cables de la fuente de Audio/Vídeo que desee modular.
Las imágenes que se muestran son para nes ilustrativos, el aspecto nal del producto puede variar.
NOTA IMPORTANTE:Para la protección de su
equipo y su correcto funcionamiento, es necesario conectar el modulador a una toma de tierra.
B - Conecte la toma de tierra tal y como se muestra en la gura.
A
B
C
B - Conecte la toma de tierra tal y como se muestra en la gura.
BB
Conexión de toma de tierra
D - Conecte un cable con conector “F” a la salida (RF OUT) para distribuir la señal modulada.
Salida a redde distribución
E - Por último, conecte la alimentación a la toma de corriente.
Alimentación
D
E
D - Conecte un cable con conector “F” a la salida (RF OUT) para distribuir la señal modulada.
Salida a redde distribución
DD
EE
CVBS / S-VHS
0,5 - 2 Vpp
PAL / NTSC
Estéreo
0,4 - 4,8 Vpp
Vídeo (RCA o S-VHS) y Audio (RCA L y R)
75 Ω
PAL 720x576 @ 25fps / NTSC 720x580 @ 30fps
MPEG2 MP@ML
MPEG1 Layer II
PSI: PAT, PMT; SI: SDT, NIT
Sí
ETSI EN 300 744 V1.5.1
2K
1/4, 1/8, 1/16, 1/32
1/2, 2/3, 3/4, 5/6, 7/8
16 QAM / 64 QAM
47 - 862 MHz
85 dBµV
75 Ω
7-8 MHz
15 dB típ.
30 dB típ.
1 kHz
“F” hembra
230 VAC - 7,5 VDC
1,2 A @ 7,5 VDC
0 ~ +45 ºC
Español, Inglés, Portugués, Italiano, Alemán, Polaco…
162 x 156 x 51 mm / 0,64 kg
ENTRADA
Entrada de vídeo
Nivel de entrada vídeo
Modo de vídeo
Entrada de audio
Nivel de entrada de audio
Conectores de entrada
Impedancia de entrada
MODULACIÓN
Resolución de vídeo
Compresión de vídeo
Compresión de audio
Generación PSI/SI
LCN
Estándar
Portadora
Intervalos de guarda
Tasa de códigos
Constelaciones
SALIDA
Rango de frecuencias
Nivel de salida
Impedancia de salida
Ancho de banda del canal
Ajuste del nivel de salida
MER
Ajuste no
Tipo de conector
GENERAL
Alimentación
Consumo
Temperatura de funcionamiento
Idiomas
Dimensiones/Peso
De acuerdo con la directiva Europea WEEE sobre gestión de residuos de materiales eléctricos y electrónicos, este producto debe tener un tratamiento particular en su desecho.La recogida selectiva de desechos ayuda a conservar los recursos naturales y a garantizar un reciclaje que proteja la salud humana y el medioambiente. Para obtener información adicional sobre los lugares en los que puede deshacerse de equipos eléctricos y electrónicos, póngase en contacto con las autoridades competentes de su localidad o con el vendedor que le suministró el producto.
, observe que el carácter aparece sombreado y seleccione
hasta el nal de la línea (observe que no parpadea ningún caracter) y presione “OK”. El nuevo nombre quedará almacenado en memoria.
El ajuste del BITRATE de vídeo y audio debe hacerse dentro de los límites permitidos para la conguración de Fuente deaudio/vídeo
C - Conecte los cables de la fuente de Audio/Vídeo que desee modular.
Las imágenes que se muestran son para nes ilustrativos, el aspecto nal del producto puede variar.
Para la protección de su equipo y su correcto funcionamiento, es necesario conectar el modulador a una toma de tierra. CC
NOTA IMPORTANTE:Para la protección de su
Esta opción permite aplicar una inversión espectral a la señal modulada.
MENU AVANZADOINV. ESPECTRO
INV. ESPECTROOFF
Cambie el nombre de la red: con los botonesseleccione el carácter y pulse OK para conrmar.**
MENU AVANZADONOMBRE RED
NOMBRE REDNET A
Ajuste la relación de aspecto entre 4:3, 16:9 y Auto (según la señalización WSS de la fuente de vídeo).
MENU AVANZADORELACION ASPECTO
RELACION ASPECTO16:9
Ajuste el bitrate de vídeo (6144 – 12288 kbps)* MENU AVANZADOBITRATE VIDEO
BITRATE VIDEO6144 kbps
Ajuste el bitrate de audio (128 – 384 kbps)* MENU AVANZADOBITRATE AUDIO
BITRATE AUDIO384 kbps
Edite el Identicador de Red. Debe congurarse de acuerdo con la norma ETSI TS 101 162 y atendiendo a la reglamentación de su país.
MENU AVANZADOID. RED
ID. RED0X3200
Modulando...C28
Modulando...C28
Consulte nuestra página web www.tecatel.com para obtener más información
sobre este producto.
C
M
Y
CM
MY
CY
CMY
K
MANUAL DIM_ESP_V4.pdf 1 04/05/11 11:57
DIM - COFDM Modulator
U S E R M A N U A L
11INTRODUCTION
22SAFETY INSTRUCTIONS
33OPERATING ADJUSTMENTS
44CONNECTIONS
55INSTALLATION
66INSTALLATION EXAMPLE
77TECHNICAL SPECIFICATIONS
Thank you for buying this digital terrestrial modulator. Please read this manual carefully to install, use and maintain the modulator in the best conditions of performance. Keep the manual at hand for future reference. The product you have adquired is a state of the art whose main characteristics are:
DVB-T Modulator compatible with standard ETSI EN 300 744 v1.5.1 Fully compatible with DVB-T / H. CVBS video input (via RCA port) or S-VHS. Stereo. VHF and UHF band (47 ~ 860 MHz) Generation of PSI tables: PAT, PMT, SI: SDT, NIT. Generation of LCN. Video formats PAL and NTSC. 2K mode operation. Constellation of 16QAM and 64QAM.
The supervision and control of DIM is done through LCD display on the front panel. It is congured through a set of intuitive navigation menus.
Any tampering can be dangerous and can perform the warranty invalid. The modulator is powered with a voltage of 7.5 Vdc. The power supply voltage must not exceed that otherwise the modulator could suffer irreparable damage and subsequent invalidation of the warranty. Therefore: - Do not replace the power supply with a voltage greater than 7.5Vdc. - Do not connect the modulator to the power if the power cord is damaged. - Do not plug the modulator into the mains supply until all cables have been connected correctly. - Do not cut the cord. Modulator shall not be exposed to dripping or splashing water and no objects lled with liquids, such as vases, shall be placed on it. Avoid placing modulator next to central heating components and in areas of high humidity. Do not cover the modulator elements that obstruct the ventilation slots and avoid overheating. If the modulator has been kept in cold conditions for a long time, keep it in a warm room no less than 2 hours before plugging into the mains. Mount the modulator in vertical position with connections located on the bottom side. From top, front and bottom of installed modulator must be at least 10 cm free space. Connect modulator to ground connection with terminal provided (see point 5-B)
Default conguration is:- Output channel: 28- Attenuation: 30%- Constellation: QAM16- FEC: 3/4
3.2 FAST CONFIGURATION
3.3 ADVANCED CONFIGURATION.
- Guard interval: 1/16- Video PID: 33- Audio PID: 34- Channel region: WESTERN EUROPE
- Network name: NET A- Channel name: CH A- Video input: CVBS- Video standard: PAL.
When modulator is booting display shows rmware version during 4 seconds.Next message shown is: "Booting ..." during that period of time the module is loading the rmware and initiating internal devices. Once started on the screen: "Running ... XX (FFFFFF) kHz". This message indicate modulator output channel, where XX is channel number (may vary between E2 and C69) and FFFFFF is frequency in kHz including ne adjustment.
Switch the menu language to English holding simultaneously down buttons at power on.
3.1 MODULATOR BOOT
With buttons you can do a fast channel change, press for conrmation.
OUTPUT CHANNELC60 (786000 kHz)
BASICMENU
OK
Adjust output level.
Select language of the menu.
Press OK to enter menu. Select “BASIC MENU” and press OK to enter.
In this menu you can change basic parameters as: Output channel, attenuation and language.
BASIC MENUOUTPUT CHANNEL
OUTPUT CAHNNELC60 (786000 kHz)
BASIC MENUATENUACION
ATTENUATIONXXX %
BASIC MENULANGUAGE
LANGUAGEENGLISH
BASIC MENUEXIT
With buttons change output channel and press OK to conrm.
Fine adjust of central frequency (± 100KHz).
Adjust output level.
Change constellation (QAM16, QAM64)
FEC adjustment (1/2, 2/3, 3/4, 5/6, 7/8).
Guard interval adjustment (1/8, 1/16, 1/32).
Video / Audio PID selection (33 – 8190).
Adjust Logic Channel Numbering, you can congure logic position of your modulated channel on your network.
Select video input.
Select video standard. PAL/NTSC.
Return to factory default.
Adjust video Brightness/Contrast/Saturation
Select language of the menu.
Press OK to enter menu, select “ADVANCED MENU” and press OK to enter. This menu allows you to adjust advanced parameters of modulator.
ADVANCED MENUOUTPUT CHANNEL
OUTPUT CHANNELC60 (786000 kHz)
ADVANCED MENUFINE ADJUST
FINE ADJUST786000 kHz
Select channel region to be used.ADVANCED MENUCHANNEL REGION
CHANNEL REGIONWESTERN EUROPE
ADVANCED MENUATTENUATION
ATTENUATIONXXX %
ADVANCED MENUCONSTELLATION
CONSTELLATIONQAM16
ADVANCED MENUFEC
FEC7/8
ADVANCED MENUGUARD INTERVAL
GUARD INTERVAL1/16
ADVANCED MENUVIDEO PID
VIDEO PID33
ADVANCED MENUCHANNEL NAME
CHANNEL NAMECH A
ADVANCED MENULCN
LCN3
ADVANCED MENUVIDEO SOURCE
VIDEO SOURCECVBS
ADVANCED MENUVIDEO STANDARD
VIDEO STANDARDPAL
ADVANCED MENUBRIGHTNESS
BRIGHTNESS123
ADVANCED MENULANGUAGE
LANGUAGEENGLISH
ADVANCED MENUDEFAULT CONFIG.
ADVANCED MENUEXIT
Change channel name: with select char to change and press OK to conrm**
With buttons change output channel and press OK to conrm.
Change name.Select char to be changed with buttons, char appears blinking, press OK to select char (it appears underlined) and with select new char, conrm change with OK. To save new name, press until end of line (see that any char appears blinking ) and press OK. New name will be stored in memory.
The audio and video BITRATE adjustment should be done within the margins allowed by the selected modulation conguration (constellation, FEC, guard interval).
Power supply connection: 7.5VDC/2ARS-232 connectionRF output.S-VHS input.RCA video.RCA Right audioRCA Left audio.Ground connection.
1
2
3
5
6
7
4
8
A - Screw modulator where you want to install it.
Audio/VideoSource
C - Connect cables to audio/video source.
Images shown are for illustrative purpose, the nal product appearance may vary.
WARNING:For the protection of your
equipment and its proper working is necessary to connect the modulator to a ground connection.
B - Connect modulator ground to installation ground, as shown in picture.
C
Ground connector
D - Connect RF out to distribute modulated signal.
E - Finally, connect power supply to main plug.
Power supply
E
D - Connect RF out to distribute modulated signal.
EE
CVBS / S-VHS
0,5 - 2 Vpp
PAL / NTSC
Stereo
0,4 - 4,8 Vpp
Video (RCA o S-VHS) - Audio (RCA L y R)
75 Ω
PAL 720x576 @ 25fps / NTSC 720x580 @ 30fps
MPEG2 MP@ML
MPEG1 Layer II
PSI: PAT, PMT; SI: SDT, NIT
Yes
ETSI EN 300 744 V1.5.1
2K
1/4, 1/8, 1/16, 1/32
1/2, 2/3, 3/4, 5/6, 7/8
16 QAM / 64 QAM
47 - 862 MHz
85 dBµV
75 Ω
7-8 MHz
15 dB typ.
30 dB typ.
1 kHz
“F” female
100 - 240 VAC - 7,5 VDC
1,2 A @ 7,5 VDC
0 ~ +45 ºC
Spanish, English, Portuguese, Italian, German, Polish...
162 x 156 x 51 mm / 0,64 kg
INPUT
Video input
Video input level
Video mode
Audio input
Audio input level
Input connectors
Input impedance
MODULATION
Video resolution
Video Compression
Audio compression
PSI/SI generation
LCN
Standard
Carrier
Guard intervals
Code rate
Constellations
OUTPUT
Frequency range
Output level
Output impedance
Channel Bandwith
Output level adjustment
MER
Fine tuning
Connector type
GENERAL
Power supply
Consumption
Temperature range
Languages
Dimensions / Weight
According to the WEEE (Waste Electrical and Electronic Equipment) EU Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product.
This option allows to do a spectral inversion in modulated signal.
ADVANCED MENUSPECTRUM INV.
SPECTRUM INV.OFF
Adjust video bitrate (6144 – 12288 kbps)* ADVANCED MENUVIDEO BITRATE
VIDEO BITRATE6144 kbps
Adjust audio bitrate (128 – 384 kbps)* ADVANCED MENUAUDIO BITRATE
AUDIO BITRATE384 kbps
Edit the Network ID. Note the Network ID should be set according to the ETSI TS 101 162 Norm and following your country regulation.
ADVANCED MENUNETWORK ID
NETWORK ID0X3200
Change network name: with select char to change and press OK to conrm**
ADVANCED MENUNETWORK NAME
NETWORK NAMENET A
Select aspect ratio between 4:3, 16:9 and Auto (based on the WSS from video source)
ADVANCED MENUASPECT RATIO
ASPECT RATIO16:9
To distribution networkRunning...C28
Running...C28
D
A
ENG
ADVANCED MENU
Visit our web page (www.tecatel.com) to obtain further information about this product.
2 3
4 5 6 7 8
1
BB - Connect modulator ground to installation ground, as shown in picture.
Ground connector
BB
Select char to be changed with buttons, char appears blinking, press OK to select char (it appears underlined) and with select new char, conrm change with OK. To save new name, press until end of line (see that any
The audio and video BITRATE adjustment should be done within the margins allowed by the selected modulation Audio/VideoSource
C - Connect cables to audio/video source.
Images shown are for illustrative purpose, the nal product appearance may vary.
For the protection of your equipment and its proper working is necessary to connect the modulator to a ground connection. CC
WARNING:
SECURITY CAMERA
SAT RECEIVER
DVD PLAYER
C
M
Y
CM
MY
CY
CMY
K
MANUAL DIM_ENG_V4.pdf 1 04/05/11 11:57
Recommended