Upload
omar-roa
View
96
Download
6
Embed Size (px)
Citation preview
62
Tipo de brida Montaje al tubo
Según tipos anteriores
Igual queWELDING NECK
con cuello mas largo
Presión nominal libras/pulgada2
150 300 400 600 900 1500 2500
1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -36´́ 1/2´́ -24´́ 1/2´́ -12´́
BRIDAS DE CUELLO PARA SOLDAR
Para condiciones de servicio muy severas
1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -36´́ 1/2´́ -24´́ 1/2´́ -12´́
BRIDAS PARA SOLDAR TUBO DENTRO
Para condiciones de servicio menos severas
1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -12´́
BRIDAS ROSCADAS
Aplicaciones especiales. Cuando el material no es soldable
1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -12´́
BRIDA LOCA CON TUBO REDONDEADO
Para pequeñas presiones. Frecuentes desmontajes
1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -42´́ 1/2´́ -36´́ 1/2´́ -24´́ 1/2´́ -12´́
BRIDAS CIEGAS (Tapas)
1/2´́ -24´́ 1/2´́ -4´́ 1/2´́ -4´́ 1/2´́ -3 1/2´́ --- 1/2´́ -2 1/2´́ ---
BRIDAS PARA SOLDAR, CON TOPE PARA TUBO
Para alta presión y pequeño diámetro
1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -24´́ 1/2´́ -12´́
BRIDAS DE REDUCCION (Tipos 2 y 3)
Empalme de tubos de diámetros desiguales
--- 1´́ -42´́ 1´́ -12´́ 1´́ -12´́ 1´́ -12´́ 1´́ -12´́ ---
BRIDAS DE ORIFICIO CON TORNILLO SEPARADOR
Se emplean para medir líquidos y gases
1´́ -42´́ 1´́ -42´́ 1´́ -42´́ 1´́ -42´́ 1´́ -36´́ 1´́ -24´́ 1´́ -12´́
BRIDAS PARA SOLDAR CON CUELLO LARGO
Generalmente para calderas
NOTA: Los espesores indicados en las bridas a partir de DN-500, son orientativos, ya que la norma no indica el espesor concreto.
BRIDAS DE ACERO FORJADODIMENSIONES ANSI B16.5
Y MSS-SP44
Welding neck
Slip-on
Screwed threaded
Lap joint
Blind
Socket welding
Reducing
Orifice
Long weldneck