Upload
ricardo-barros
View
219
Download
0
Embed Size (px)
Citation preview
8/17/2019 Hoja de Datos Bombas RAS PTAR
1/8
Data sheet
Customer item no.:Communication dated: Number: ES 4323576
Doc. no.: Item no.: 100
Quantity: 8 Date: 12/05/2016Page: 1 / 8
Sewatec K 300-401G 3EN 225S 08 Version no.: 1
Operating data
Design
Suction nozzle drilled acc. to DIN2501 with tapped blind holes
Requested flow rate 170.000 l/s
Requested developed head 6.00 m
Pumped medium Wastewater, municipalmechanically treatedNot containing chemical andmechanical substances which
affect the materials Ambient air temperature 30.0 °CFluid temperature 30.0 °C
Fluid density 999 kg/m³
Actual flow rate 170.000 l/s
Actual developed head 6.00 m
Efficiency 80.1 %
Power absorbed 12.58 kW
Pump speed of rotation 736 rpm
NPSH required 3.20 m
Permissible operatingpressure
10.00 bar.g
Discharge press. 0.59 bar.g
Fluid viscosity 0.80 mm²/s
Suction pressure max. 0.00 bar.g
Mass flow rate 170.44 kg/s
Max. power on curve 13.52 kWMin. allowable flow rate 67.531 l/s
Min. allow. mass flow 67.46 kg/s
Shutoff head 8.41 m
Max. allow. mass flow 265.79 kg/s
Design Single system 1 x 100 %Tolerances to ISO 9906 Class3B; below 10 kW acc. toparagraph 4.4.2
Pump standard KSB-Aggregate internationalexecution
Design Baseplate mounted, long-coupled
Orientation HorizontalSuction nominal dia. DN 300Suction nominal pressure PN 10Suction position axialDischarge nominal dia. DN 300Discharge norminal pressure PN 10Discharge position top (0°/360°)Discharge flange drilledaccording to standard
EN 1092-2
Shaft seal 2 mech. seals in tandemarrangement with oil reservoir
Manufacturer KSB
Type MGMaterial code SIC/SIC/NBRImpeller type Multivane radial flow impeller
(K)Wear ring Casing wear ringImpeller diameter 378.0 mmFree passage size 135.0 mm
Direction of rotation from drive ClockwiseBearing bracket size S05Bearing seal Lip sealBearing type Anti-friction bearingsLubrication type GreaseColor Ultramarine blue (RAL 5002)
KSB-blue
8/17/2019 Hoja de Datos Bombas RAS PTAR
2/8
Data sheet
Customer item no.:Communication dated: Number: ES 4323576
Doc. no.: Item no.: 100
Quantity: 8 Date: 12/05/2016Page: 2 / 8
Sewatec K 300-401G 3EN 225S 08 Version no.: 1
Driver, accessories
Materials G
Packaging
Outdoor storage at -40°C to +50°C for up to 3 months. Packetmust be covered. No corrosion protection, only transportprotection.
Manufacturer Flender Coupling type Eupex NNominal size 160
Coupling guard type Tread-proof (ZN3230)Guard size A2
Guard material Steel STBaseplate type Welded steel for SewatecBaseplate size H25
Driver type Electric motor Drive standard mech. IECModel (make) SiemensDrive supplied by Standard motor supplied by
KSB - mounted by KSBMotor const. type B3Motor size 225SMotor speed 736 rpm
Frequency 50 Hz
Rated voltage 400 V
Rated power P2 18.50 kW
Available reserve 47.04 %Rated current 38.5 A
Starting current ratio 5.5
Insulation class F to IEC 34-1Motor enclosure IP55Cos phi at 4/4 load 0.78
Motor efficiency at 4/4 load 94.3 %
Temperature sensor 3 PTC resistorsMotor winding 400 / 690 VNumber of poles 8Connection mode DeltaMotor cooling method Surface coolingMotor material Grey cast iron GG/CAST
IRONMotor noise pressure level 57 dBa
Pump casing (101) Grey cast iron EN-GJL-250Discharge cover (163) Grey cast iron EN-GJL-250Shaft (210) Chrome steel 1.4021+QT800Impeller (230) Grey cast iron EN-GJL-250
O-Ring (412) Nitrile rubber NBRCasing wear ring (502.1) Grey cast iron EN-GJL-250Screwed plug (903) Steel STHexagon socket head capscrew (914)
Carbon steel C35E+N
Packaging category B1 Wooden or plywoodcase, cover provided withpolyproylene cellular sheet,outdoor storage up to 3months
Packaging for transport Truck
IPPC Standard ISPM 15 Yes
Packaging for storage Indoor
8/17/2019 Hoja de Datos Bombas RAS PTAR
3/8
Performance curve
Customer item no.:Communication dated: Number: ES 4323576
Doc. no.: Item no.:100
Quantity: 8 Date: 12/05/2016Page: 3 / 8
Sewatec K 300-401G 3EN 225S 08 Version no.: 1
0 50 100 150 200 250 300[l/s]
2
4
6
8
10
[m]
367.0/331.0/327.0
Qmin
408.0/393.0/376.0
Qmin
402.0/378.0/356.0
Qmin
T o t a l d e v
e l o p e d h e a d
0 50 100 150 200 250 300[l/s]
2
4
[m] N
P S H
r e q .
0 50 100 150 200 250 300[l/s]
0
50
[%] E f f i c i e n c y
0 50 100 150 200 250 300[l/s]
8
14
10
[kW]
P o w e r I n p u
t
Flow
Curve data
Speed of rotation 736 rpm
Fluid density 999 kg/m³
Viscosity 0.80 mm²/sFlow rate 170.000 l/s
Requested flow rate 170.000 l/sTotal developed head 6.00 m
Requested developed head 6.00 m
Efficiency 80.1 %
Power absorbed 12.58 kW
NPSH required 3.20 mCurve number K42529
Effective impeller diameter 378.0 mm Acceptance standard Tolerances to ISO 9906Class 3B; below 10 kWacc. to paragraph 4.4.2
8/17/2019 Hoja de Datos Bombas RAS PTAR
4/8
Speed curve
Customer item no.:
Communication dated: Number: ES 4323576
Doc. no.: Item no.:100
Quantity: 8 Date: 12/05/2016Page: 4 / 8
Sewatec K 300-401G 3EN 225S 08 Version no.: 1
0 50 100 150 200 250[l/s]
0
5
10
[m]
736 1/min
Qmin
T o t a l d e v e l o
p e d h e a d
0 50 100 150 200 250[l/s]
2
4
[m] N
P S H
r e q .
0 50 100 150 200 250[l/s]
0
50
[%] E f f i c i e n c y
0 50 100 150 200 250[l/s]
8
14
10
[kW]
P o w e r I n p u t
Flow
Curve data
Fluid density 999 kg/m³
Viscosity 0.80 mm²/s
Flow rate 170.000 l/sRequested flow rate 170.000 l/s
Total developed head 6.00 m
Requested developed head 6.00 m
Effective impeller diameter 378.0 mm
8/17/2019 Hoja de Datos Bombas RAS PTAR
5/8
Installation plan
Customer item no.:Communication dated: Number: ES 4323576
Doc. no.: Item no.:100
Quantity: 8 Date: 12/05/2016Page: 5 / 8
Sewatec K 300-401G 3EN 225S 08 Version no.: 1
DN1
DN2
625
450
355 590
143
590
125
18
850
780
900
1140
789
215 750
ø
ø ø
ø
1)
1) he inlet flange spacer is available as an accessory
6
28
800
170
.
.
200
971
800
2000
2240
ø60 60
140
Drawing is not to scale Dimensions in mm
Motor
Baseplate
Connections
Coupling
Weight net
Connect pipes without stress or strain!Dimensional tolerances for shaft axis height: DIN 747Dimensions without tolerances, middle tolerances to: ISO 2768-m
For auxiliary connections seeseparate drawing.
Suction nozzle drilled acc. to DIN2501 with tapped blind holes
Motor manufacturer SiemensMotor size 225SMotor power 18.50 kWNumber of poles 8
Speed of rotation 736 rpm
Design Welded steel for SewatecSize H25Material Steel STLeakage drain baseplate(8B)
Rp1, Without
Foundation bolts M16x200 (Not in scope of supply)
Suction nominal size DN1 DN 300 / EN 1092-2Discharge nominal size DN2 DN 300 / EN 1092-2Nominal pressure suct. PN 10Rated pressure disch. PN 10
Coupling manufacturer Flender Coupling type Eupex NCoupling size 160Spacer 0.0 mm
Pump 630 kgBaseplate 265 kgCoupling 10 kgCoupling guard 4 kgMotor 270 kgTotal 1179 kg
8/17/2019 Hoja de Datos Bombas RAS PTAR
6/8
Installation plan
Customer item no.:Communication dated: Number: ES 4323576
Doc. no.: Item no.:100
Quantity: 8 Date: 12/05/2016Page: 6 / 8
Sewatec K 300-401G 3EN 225S 08 Version no.: 1
Connection dimensions for pumps: EN735Dimensions without tolerances - welded parts: ISO 13920-BDimensions without tolerances - gray cast iron parts: ISO 8062-CT9
8/17/2019 Hoja de Datos Bombas RAS PTAR
7/8
Connection plan
Customer item no.:Communication dated: Number: ES 4323576
Doc. no.: Item no.:100
Quantity: 8 Date: 12/05/2016Page: 7 / 8
Sewatec K 300-401G 3EN 225S 08 Version no.: 1
1M.1 6D
13B
13D
6B
8B
6B
1M.1
Connection schematic also applies to vertical installation.
Connections
1M.1 Pressure gaugeconnection
G 1/2 Drilled and plugged.
6B Pumped liquid drain G 1 Drilled and plugged.6D Pumped medium - filling /venting
G 1 1/4 Drilled and plugged.
8B Leakage drain G 1/2 Drilled and plugged.13B Oil drain G 1/2 Drilled and plugged.13D Refill / venting G 1/2 Drilled and plugged.
8/17/2019 Hoja de Datos Bombas RAS PTAR
8/8
Force and Moment Limits
Customer item no.:Communication dated: Number: ES 4323576
Doc. no.: Item no.:100
Quantity: 8 Date: 12/05/2016Page: 8 / 8
Sewatec K 300-401G 3EN 225S 08 Version no.: 1
Fz
Fy
FxFz
Discharge flange
Suction flange
(+)Fy
Fx
Drawing is not to scale
Force and Moment Limits
Suction flange Discharge flange
The forces and moments were determined on the basis of API 610 (6th edition), table 2, double values.The allowable resulting forces are to be determined by
The given force and moment limits are only applicable for static pipe loads.
A computerized strength analysis is only available on special request.The values apply for installation on completely grouted baseplates bolted to a rigid, level foundation.
Fx s 8000 N
Fy s 5350 N
Fz s 6650 N
Fres s 8550 N
Mx s 6100 Nm
My s 4600 NmMz s 3000 Nm
Valid for temperature 30.0 °C
Fx d 6650 N
Fy d (+) 4100 N
Fy d (-) 8000 N
Fz d 5350 N
Fres d 8550 N
Mx d 6100 NmMy d 4600 Nm
Mz d 3000 Nm