8/6/2019 Instruccin de armado conector DIN y N Rosenberger
MA_1C7-C03
1/2
Installation InstructionNo. : MA_1C7-C03Revision c
07.07.2009
1/2R for 1/2R annular corrugation cable
1.Cut your cable at corrugation top usinghacksaw or other tools,
then straighten thecable end for approximate 200mm.
200mm
2.Strip the cable. Press against the cable usingstripping tool
and turn slowly until strippingend. Note : Be careful not to scrape
centerconductor. ,
3.If the outer conductor have been cut atcorrugation top(as
photo 4) then go to step5,otherwise take notice of length a.
4 5a
4.Cut the center conductor for a length aby pliers.
a
5.Strip the cable again. Gently turn the tool toprevent outer
conductor distorted. Properlyprepared cable end as the photo
shows.
6.Be sure the outer conductor is round andundistorted. You can
use tools to make itround if necessary.
60S1C7-C03N1
60W110-C03
20# 20#
Tools
a
a
corrugation top
14.5 P+0.5 P 7 0.3
C0.3
m m
1 0
2 0
3 0
4 0
5 0
6 0
7 0
8 0
9 0
1 0 0
I n c h e s
1
2
3
4
7/16 DIN
Female7/16 DIN
Male
N TYPE
MaleN TYPE
Female
60K1C7-C03N1 53S1C7-C03N1 53K1C7-C03N1
Front nut
Back nut
Sealing nut
Edge
Clamp ring
8/6/2019 Instruccin de armado conector DIN y N Rosenberger
MA_1C7-C03
2/2
Rosenberger HF-Technik GmbH & Co Rosenberger Asia Pacific
Electronic Co., Ltd.Hauptstrae 1 No. 3 Anxiang Street, Block B,
Tianzhu Airport Industrial Zone D-83413 Fridolfing 101300 Beijing,
P.R. China Tel.: +49-8684-18-0 Tel.: 0086 1080481995 Fax.:
+49-8684-18-499 Fax: 0086 1080482438 e-mail [email protected]
www.rosenberger.de
7. Slide back nut onto the cable until it iscompletely seated.
Please loose sealing nut inorder to easy to install back nut
8. Press clamp ring on to out conductor,
9. Insert center conductor into flaringtools guide hole, then
press and spin thetool to flare outer conductor.
10.Proper shape after flaring operation.Please dont hurt inner
contact
,
11. Deburr by brush. 12 Push cable back until clamp ring
slide
into slot of back nut
13.Tighten front nut with back nut by hands
14.Tighten front nut and back nut withwenches until
stop(Torque:18~22NM)
( 18~22NM)
15.Tighten sealing nut withwenches (Torque:5~8NM)
( 5~8NM)
16. Finished.
1) 60W110-C03
2) 5 103)4)
Note:1) Please refer to related instruction to use 60W110-C03
stripping tool;2) You can use other tools to get proper shape and
size as photo 5 and 10 shows;3) Information in this instruction is
subject to change without notice;4) ROSENBERGER disclaims any
responsibility for the result of improper usage.
Draft Checker Approved Date Rev. Engineering change number Name
Date
Roger Songzg Kevin 15.07-2009 c 09-0480 ZhaiQK 14.07.2009
