Avioneta para imprimir

8/10/2019 Avioneta para imprimir

1/12

Spirit of St. Louis : Assembly Instructions

PAGE01

The Spirit of St. Louis (also known as the Ryan NYP-1) is a single-engine plane that was successfully

flown by Charles Lindbergh as a solo non-stop transatlantic flight. The main external features of the

craft were its lack of front windshield, and its wings, which were extremely long compared to its body.The aircraft took off from New York's Long Island and flew 5,810km to Paris. The journey took 33

hours, 29 minutes and 29.8 seconds, which was regarded as quite fast at the time. It was the first solo,

non-stop flight to travel this route.

This papercraft Spirit of St. Louis is about one twenty eighth the size of the real Spirit of St. Louis.

*This model was designed for Papercraft and may differ from the original in some respects.

Glue tab notation key

Glue

Each glue tab has a symbol andnumber printed on it.

Glue with in the same part.

(Dotted line)Mountain fold

Guide rod

How to make the cylinders

This craft involves making cylinders

with diameters of 3 to 7mm, so it may

be helpful to have some rods of sizes

about 0.5mm thinner handy.

Assembly Instructions

Wrap around and glueto the top of the cylinder.

(Dashed and dotted line)Valley fold

(Solid line)Scissors line

You may like to use

a metal rod as a guide.

Layer wrapping (roll)Wrap around and glue to thecylinder,to use as a glue tab

(Red solid line)Cut in Line

Completed partsbecome a cylinder

Trace along the folds with a ruler anda used pen (no ink) t o get a sharper,easier fold.

Glue, scissors and other tools may be dangerous toyoung children so be sure to keep them out of thereach of young children.

Parts list (Assembly Instructions) : Twelve A4 sheets

No. of Parts: 177

*Bulid the model by carefully reading theAssembly Instructions,

in the parts sheet page order.

Spirit of St. Louis


2/12

PAGE02 Scissors line Mountain fold Valley fold Cut outCut in Line


2-B2-C2-D

2-F

2-E 2-A

2-J

2-M

2-W

2-X

2-W

2-X-1

2-X-1

2-P-1

2-W

2-Y

2-Y-1

2-I

2-I

2-Z-1

2-Z-2

2-P-2

2-P-2

2-Z

2-C/2-D

2-F/2-E

2-A/2-B


3/12

PAGE03


Scissors line Mountain fold Valley fold Cut outCut in Line

2-T

2-P

2-R

2-Q

2-Q/R

2-P

2-S

2-Q-1

3-C

3-B

2-K

2-L 2-L-1

2-K/2-K-12-L/2-L-1

Insert in between 2-W

and 2-J/M and attach.

Insert the long glue tabs

on 2-S through the holes

in 2-Q/R and fasten them

to the glue tabs on 2-P.

2-P-1

3-D

3-E-1/3-A-1

2-S

3-D

3-E/3-E-1

Insert the protruding parts of 3-B

into the holes on 3-A/3-A-1/3-E/3-E-1,

fold them and attach them to the

protruding parts of 3-D.

Do not put glue on 3-A/3-A-1/3-E/3-E-1.

3-E/3-A

3-S-1/3-S

After attaching

the tail assembly,

attach it to 2-P-1.

After gluing, check that the parts move.

2-K-1

2-P/Q is moveable.


4/12

PAGE04



3-G

2-O

3-F

2-U

2-N

2-H

4-E

4-E-1

3-H

4-D-1

4-D

4-C-1

4-C

2-G

Attach 2-O in linewith the fold lines

on 3-F and 3-G.


5/12

PAGE05



Cross-sectional diagram of how to glue the engine parts

With the bumpy ends omitted Push in towardsthe center.

Glue thecenter joiningparts together.

Bendtowardsthe back.

Push in towardsthe center.

3-L

3-I

3-I 3-I

3-Q

3-R

3-P

3-O

3-N

4-Q

4-K

4-O

4-O/4-P

4-L

4-O

4-P

Align these parts on 4-P/4-O.

4-P

4-R

3-M


6/12

PAGE06



Cross-sectional diagram of how to assemble t he propellor shaft

Only put glue on 4-M. In step , before attaching

4-H to 4-K, check that the 4-K parts rotate.

4-J

4-M

4-M

4-H

4-H

4-Z

4-Z

4-H

4-N

4-N

4-O/P4-N

4-K

4-H

4-U

4-W

4-U/4-W

3-K

4-U/4-W

4-H

4-Z

3-Q/R

4-M

4-M

4-J

4-R

4-J

4-K4-J

Cut a slot.Add a curve tothe 4-Z glue tabs.

Glue the 4-Z glue tab partsto the inside of 4-H.

*Do not glue 4-J.

*Do not glue 4-J/4-K.

*Glue 4-H to 4-K.

*Add a curve to 4-U/4-W after gluing.

*Curve it as shown.

*Insert 4-U/4-W into the slots

on 4-H and attach.


7/12

PAGE07



5-C/6-C

5-C/6-C

5-B/6-B

5-I/6-G

5-H/6-F

5-A/6-A

5-F

5-F

5-F/5G

5-G

5-G

5-E/6-E

5-D/6-D

*Make 10 pairs altogetherof 5-D/6-D/5-E/6-E.

Make two pairs.

Where to attach 5-F/5-G.


8/12

PAGE08



5-I/6-G

5-H/6-F

Side view after gluing

Start gluing from the folded side and work back.

5-A/6-A

5-A/6-A

5-D/6-D

5-D/6-D

5-A/6-A

5-B/6-B

5-B/6-B is moveable

so do not put glue on

the wing.

5-A

6-A*Attach the tip ofthe wing together first.

*Insert 5-B/6-B into the wing. (Do not add glue.)

*The 5-A/6-A wing is assembled in the same way.

Place 5-A/6-A on the template on page 7 of the parts sheet as shown in the figure below and attach them in line with the black lines.

Plane side of wing

Fold in without gluing.

Moves up and down.

Moves up and down.

Papertemplatetoattachtothewing5-D/6-D.

Align the tips of 5-D/6-D with thefold line of the glue spot on5-A/6-A, and begin to attach.

Attach 5-D/6-D at a position so thatthe glue spot is folded 45 .

*After completing steps and ,attach the wing together.


9/12

PAGE09



3-U/3-U-1

3-U/

3-U-1

6-I/6-H

6-I/6-H

6-H

3-J/3-Y

3-J/3-Y

4-I

4-I

4-A/4-B

3-X/3-X-1

3-X/3-X-1

4-S/4-T

7-K

4-S/4-T

3-W/3-W-1

3-W/3-W-1

4-A/4-B

3-T-1 3-T-1

7-K

5-A/6-A

3-L

6-I

Wings

Align the tip of 3-L with the wings,fold the edge forward and attach.

Wrap around

4-A/4-B andattach.

3-U-1

3-U

3-Y

4-A

3-J

4-B


10/12

PAGE10



4-G

4-F

4-F

4-F4-F

3-T 3-Z

3-T

7-E7-E

7-E

Glue spot

7-E

4-G

4-G

4-G

Slot 7-E onto 4-A/4-B,and attach to the body.

Slot 7-E onto 7-C/7-D,and attach to the body.

Wrap 3-T/3-Z around3-U and attach.

7-A

7-B

7-B

7-C

7-D

7-D

Body

Attach to the body.

Put glue on 4-G/4-Fand attach.


11/12


12/12

PAGE12



Documents

Avioneta para imprimir